NACE Paper 14433-2020 CO₂中O₂含量對X65低碳鋼在氣態、液態和超臨界CO₂環境中的腐蝕行為影響

Effect of O2 Content in CO2 on Corrosion Behavior of X65 Low Carbon Steel in Gaseous, Liquid and Supercritical CO2 Environments

NF L13-205*NF EN 3887:2001 航空航天系列 耐熱合金CO-WH4101（CoCr20W15Ni）焊接用填充金屬

Aerospace series - Heat resisting alloy CO-WH4101 (CoCr20W15Ni) - Filler metal for welding

XP PR EN 2712-005:1996 航空航天系列 - 一般用途的單導體和多導體電纜 - 工作溫度在 - 55 攝氏度和 150 攝氏度之間 - 第 005 部分：鎧裝（覆蓋）和護套，可使用 CO 激光打標...

Aerospace series - Cables, electrical, single and multi-conductor, for general use - Operating temperatures between - 55 degrees Celsius and 150 degrees Celsius - Part 005: armored (wrapped) and sheaths, markable with CO laser...

BH GSO OIML R144-2:2022 用于連續測量固定源排放中 CO 和 NOx 的儀器 第2部分：測試程序

Instruments for the continuous measurement of CO and NOx in stationary source emissions- Part 2: Test procedures

CP 118:1969 鋁的結構用途

The structural use of aluminium

NACE Paper 13026-2019 實驗研究鹽濃度對均勻CO₂腐蝕的影響

Experimental Study on the Effect of Salt Concentration on Uniform CO2 Corrosion

BS PD CEN/TR 17310:2019 碳酸化和CO₂混凝土中的吸收

BS PD CEN/TR 17310:2019 provides detailed guidance on the carbonation and carbon dioxide (CO2) uptake in concrete. This guidance is complementary

Carbonation and CO₂ uptake in concrete

DS/EN 3888:2001 航空航天系列 耐熱合金 CO-WH1402（CoCr22Ni22W15）焊接用填充金屬

This standard specifies the requirements relating to: Heat resisting alloy CO-WH1402 (CoCr22Ni22W15) Filler metal for welding for aerospace

Aerospace series - Heat resisting alloy CO-WH1402 (CoCr22Ni22W15) - Filler metal for welding

NF L13-206*NF EN 3888:2001 航空航天系列 耐熱合金CO-WH1402（CoCr22Ni22W15）焊接用填充金屬

Aerospace series - Heat resisting alloy CO-WH1402 (CoCr22Ni22W15) - Filler metal for welding

NBN 50 ADD 12-1987 家用及類似用途的設備 家用及類似用途的兩孔插銷

Equipment for household and similar purposes Two-hole plugs for household and similar purposes

UOP 603-2013 通過 GC 跟蹤氫氣和輕質氣態烴中的 CO 和 CO2

Trace CO and CO2 in Hydrogen and Light Gaseous Hydrocarbons by GC

DS/EN 3887:2001 航空航天系列 耐熱合金CO-WH4101（CoCr20W15Ni）焊接用填充金屬

This standard specifies the requirements relating to: Heat resisting alloy CO-WH4101 (CoCr20W 15Ni) Filler metal for welding for aerospace

Aerospace series - Heat resisting alloy CO-WH4101 (CoCr20W15Ni) - Filler metal for welding

LST EN 3888-2002 航空航天系列 耐熱合金 CO-WH1402（CoCr22Ni22W15）焊接用填充金屬

Aerospace series - Heat resisting alloy CO-WH1402 (CoCr22Ni22W15) - Filler metal for welding

UNI EN 3959:2001 航空級 鈷基合金CO-B41601（CoCr19Ni17Si8W4） 焊接用金屬粉或膏狀物

La presente norma è la versione ufficiale in lingua inglese della norma europea EN 3959 (edizione giugno 2001). La norma è parte di una

Aerospace series - Cobalt base alloy CO- B41601 (CoCr19Ni17Si8W4) - Filler metal for brazing - Powder or paste

TCVN 7242-2003 醫療用固體廢物焚化爐.廢氣中一氧化碳濃度(CO)的測定方法

Health care solid waste incinerators.Determination method of carbon monoxide concentration (CO) in fluegas